
ZDFJ76A1
ZDFJ76A1 Single-Boom Drilling Jumbo Manufacturer
A single-boom face-drilling option for a development heading. Specify the hole pattern, feed and required operating envelope.
Discuss configuration, documentation and delivery terms directly with ZONGDA.
SPECIFICATION REVIEW
ZDFJ76A1 reference data
| Drilling arrangement | Single boom |
|---|---|
| Hole diameter in technical sheet | 32–76 mm |
| Machine width in technical sheet | 1910 mm |
| Machine length in technical sheet | 11200 mm |
| Drilling power arrangement | Electro-hydraulic |
APPLICATION & PROCUREMENT
Review the working task
ZDFJ76A1 is a single-boom electro-hydraulic drilling jumbo for underground face-development enquiries. Its technical sheet lists a hole diameter range of 32–76 mm, a machine width of 1910 mm and a machine length of 11200 mm. These reference dimensions give a purchasing team a useful starting point; the proposed feed and boom arrangement still needs to be matched to the heading.
For buyers comparing a single-boom drilling jumbo manufacturer, the practical question is which documented configuration reaches the required holes and fits the route. ZONGDA's model documents describe the carrier, drilling equipment and utilities, but contain different coverage statements. This page therefore does not assign one universal working area to every ZDFJ76A1 offer.
Include in your inquiry
- Face width, height and hole pattern
- Hole diameter, depth and rock conditions
- Electrical supply, water and travel restrictions
Configuration and selection
Begin with a drawing of the face. Show width, height, planned hole locations, diameter and depth, then identify the places where feed positioning may be constrained. Maximum width and height alone cannot describe whether the proposed boom reaches a particular corner or hole direction. Ask for a coverage drawing associated with the actual feed, rod and rock drill in the offer.
Review access as a separate purchase condition. The published width and length do not establish the turning envelope, travelling height or setup clearance of the supplied configuration. Include bends, services and the narrowest usable sections in your enquiry. The single-boom versus twin-boom guide helps structure a comparison with ZDFJ76A2 when both arrangements are under consideration.
Application requirements
Use this model enquiry for a development face rather than substituting production-hole requirements into a face-jumbo specification. Epiroc's underground drilling overview distinguishes face jumbos from production rigs. That industry distinction is relevant to equipment selection; it does not establish this model's performance.
A useful application brief describes the rock conditions and the intended drilling pattern, together with the available power and water. If the same machine is expected to undertake other drilling tasks, list each task separately and ask which feed arrangement applies. A general brochure description is not a substitute for a configuration-specific proposal. Keep engineering approval of the mine's working arrangement separate from the equipment quotation.
Supplier quotation and scope of supply
Request a ZDFJ76A1 factory quotation with the complete model identifier and a defined supply scope. Ask the supplier to identify the rock drill, feed, boom, rod arrangement and carrier drawing by revision. Electrical requirements should state the selected supply voltage, frequency and starting arrangement, while utility information should identify the required water and air interfaces.
- Attach the face pattern, route sketch and required hole diameter and depth.
- List requested quantities, delivery destination and the documents your project must review.
- Ask for included tooling, commissioning scope and recommended initial spares to be itemised.
- Request delivery, warranty and commercial terms in writing for the proposed configuration.
Compare the same package across offers. A lower equipment price may refer to a different feed, omitted tools or a narrower service scope. Resolve those differences before treating the proposals as equivalent. The original technical sheet provides the reference basis for the initial discussion, while the final quotation should identify any departures from it.
If a quotation leaves a dimension or service requirement unanswered, record it as an open clarification. Resolve it against the offered machine drawing before completing the technical purchase review.
ZDFJ76A1 procurement FAQ
What hole diameter is documented for ZDFJ76A1?
The technical sheet lists 32–76 mm. Confirm the bit, rod, shank and rock-drill package for your required hole size. A published diameter range does not mean that every tooling combination is included in the price.
What coverage area should be used for purchasing?
Request a configuration-specific coverage diagram. The supplied technical sheet and brochure use different coverage descriptions, so selecting the largest figure would produce an unreliable purchase requirement. Send the actual face pattern and ask the manufacturer to mark the proposed working envelope against it.
Does a single boom determine site output?
No fixed output is stated here. Hole layout, rock conditions, repositioning and site services all need to be considered in a project assessment. If output is a purchasing criterion, ask the supplier to explain the assumptions behind any proposed estimate rather than comparing boom counts alone.
Ordering and after-sales support
Can the proposed drilling configuration be customized?
Product-specification customization is available for discussion with ZONGDA. Send the face layout, hole requirements and site constraints with your request. Have the team identify which changes it can supply and document the accepted configuration; a general customization statement does not establish a new drilling capability.
When should I place a drilling-equipment order?
The company's general order guidance is normally one to two months. Expedited production is supported and stock is sometimes available, but neither confirms availability of this drilling model. Include your required site date and destination so ZONGDA can quote the current production and delivery arrangement.
Can ZONGDA support commissioning and maintenance?
ZONGDA lists installation and commissioning, spare-parts supply, and online and local technical support among its services. Tell the team where the equipment will operate and what assistance you need. Confirm the applicable service arrangements and warranty policy with the machine offer, including any proposed on-site work.
Payment, delivery and service arrangements
Discuss This OrderSource document and next checks
Read the original supplied technical document alongside these selected reference figures. Confirm the current revision and configuration in your quotation.
Open original technical file (PDF)SPECIFY YOUR REQUIREMENT
Bring the operating conditions.
Request the right configuration.
Include drilling task, face coverage, site utilities, quantity and delivery destination in your inquiry.